Konica minolta bizhub 558e error codes Replace the eMMC board. Bizhub 558e we reset it twice its working don't jinx me lol I did download a new updated firmware for my next visit if it continues to fail keep me in the loop as we need to figure out a positive fix for this werid code brent Comment. ](Only in bizhub 658e/558e/458e) The machine When an error is detected, the following message appears. Causes: • Fusing motor (M3) • Paper conveyance motor (M101) • Paper feed sensor (PS201) • FS control board (FSCB) Remedy: 1 Initial check items - - 2 PS201 I/O check, Code: C3B03 Description: IH malfunction (monitor) • Though the IH heater is ON, this status cannot be detected mechanically. Code: C3825 Description: Fusing abnormally low temperature detection (Main of the heating roller) The heating roller temperature sensor (TEMS) continues to detect a temperature lower than a predetermined one for a predetermined period of time. Causes: • Fusing unit • DC power supply (DCPU) • MFP board (MFPB) Remedy: 1. The wrong model of firmware is detected in the engine during the initial connection to the engine is being checked 3. Code: C3102 Description: Heating roller assy failure to turn During any state other than printing operation , the hard latch signal from one or both of the heating roller rotation latch detection 1 and the heating roller rotation latch detection 2 is turned ON. Causes: • Toner suction fan (FM11) • MFP board (MFPB) Remedy: 1. Turn OFF the main power switch, disconnect and then connect the power cord. % For information on the default administrator password, refer to About Press Copyright Contact us Creators Advertise Developers Terms Privacy Policy & Safety How YouTube works Test new features NFL Sunday Ticket Press Copyright (bizhub 658e/558e) 4. 3 M1 operation check PRCB CN31-2 (bizhub 658e/558e) 4. Code: C0000 Description: Main Motor malfunction • The Main Motor (M1) Lock signal remains HIGH for a continuous 1-sec. Causes: • Transport motor (M1) • Tray 1 paper feed clutch (CL3) • Registration clutch (CL4) • Registration sensor (PS1) • Front side board (FRB) • MFP board (MFPB) Code: 13-01, 13-40 Description: Misfeed at tray 3 feed section. 3 Replace MFPB Code: C392A Description: Heating roller temperature sensor contamination (Main of the heating side). ] -> [HDD Format], and conduct the HDD format function. It's a copier with an error code of c-1144, Konica Minolta, hub C364, Yes double checked the code and checked for paper All About this machine. Code: C5102 Description: Transport motor’s failure to turn. Konica-Minolta bizhub C224; Konica-Minolta bizhub C224e; Konica-Minolta bizhub C284; Konica-Minolta bizhub C284e; Konica-Minolta bizhub C364; Konica-Minolta bizhub C364e Konica-Minolta bizhub 308e; Konica-Minolta bizhub 368e; Konica-Minolta bizhub 458e; Konica-Minolta bizhub 558e; Konica-Minolta bizhub 658e Code: C3B02 Description: IH malfunction (CPU). Reboot the machine. Causes: • Tray 4 paper feed motor (M121) • Used for the following models. Out of five scanning attempts, only one is successful. Code: C5360 Description: Clean unit fan's failure to turn (When CU-202 is installed) The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. or more after connect the power cord, and turn ON the main power switch. The wrong model of firmware is detected in the engine during the initial connection to the engine is being checked Code: 66-01, 66-11, 66-21 Description: bizhub 368e/308e Misfeed at DF turnover section 66-01 <When DF-629 is installed> The document registration sensor (PS3) is not turned ON (unblocked) by the paper even after the set period of time has elapsed after Konica-Minolta bizhub 558e Parts Catalog - Table Of Contents. Code: 10-01, 10-02, 10-04, 10-40 Description: bizhub 658e/558e/458e Misfeed at manual bypass feed section 10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor/1 (PS1) even after the lapse of a given period of time after the manual bypass tray starts to Code: 99-03 Description: Image stabilization not completing a job. Causes: • Machine rear side cooling fan (FM3) • MFP board (MFPB) Remedy: 1. 2 Check M1 for proper drive coupling and correct as necessary. 1 Introduction Thank you for purchasing our product. Most of the time C-E301 is resolved by FW, on the last page of the management list there are codes, normally a zero, followed by an "x" then a series of letters and numbers, the "Read me" bulletin that comes with each FW normally lists what is "fixed", a lot of the times they are "C-E301" errors, followed by the code, a couple of years ago, I thought I'd list them, in The maintenance sign indicates that the copier needs to be well serviced and checked if something is to be replaced or not. 2 Code: C3B07 Description: IH input power error. 1 Introduction 1 1 Security 1. Wait for 10 sec. 2 Check the fusing unit, DCPU and PRCB for proper connection and correct or change as necessary. Causes: MFP board (MFPB) Remedy: 1. Consumables such as Toner, Drum unit, Fuser unit, rollers, and Developer unit are changed at such times. Open and close the lower front door. Replace the fusing unit. (Malfunction of IH heater operation) Code: 10-01, 10-02, 10-04, 10-40 Description: bizhub 658e/558e/458e Misfeed at manual bypass feed section 10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor/1 (PS1) even after the lapse of a given period of time after the manual bypass tray starts to M4 load check • Check code: 60 • Multi code: 81, 82 • Control signal: DFCB J18-4 to 5 • Location of electrical component: DF-704 1-G 6. bizhub 658e/558e/458e/368e ; Konica Minolta bizhub 458e | bizhub 658e/558e/458e/368e/308e Quick Start Guide - Page 181 Settings] - [Install License] - [To- ken Code]. <When FS-537 or FS-537SD is installed> The FNS middle sensor (PS36) is not turned ON even after the set period of time has elapsed after the FNS entrance sensor (PS34) is turned ON by the paper. 5 Replace DCPU. Keypad KP-101 Page 2 BIZHUB 558/368 QUICK REFERENCE 3/4 Finishing Scan operations – Scan/Fax screen* Register a scan/fax program Code: 66-02, 66-12; Description: bizhub 658e/558e/458e Misfeed at DF paper feed section. If you cannot resolve the error, write down the Parameter error of the certificate (EAP-TLS/EAP-TTLS/PEAP). 2 Replace the hard disk. <bizhub 554e> The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. Replace M4. 13-40 For paper fed from the tray 3, the image write start signal permit continues to be disabled for a predetermined period of time Code: C5304 Description: Fusing power supply cooling fan's failure to turn. The fan lock signal remains HIGH for a predetermined continuous period of time while the fan is turning. Take the appropriate action according to the message displayed on the screen. This User's Guide contains the operating procedures and precautions to be used when using the security functions offered by the bizhub 658e/558e/458e machine. The connection has been interrupted. (bizhub 368e/308e / bizhub 658e/558e/458e) Code: CD010 Code: 20-01, 20-02, 20-04 Description: bizhub 658e/558e/458e Misfeed at vertical transport section. <When PC-210 is installed> • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. Code: 99-04 Description: bizhub 368e/308e Controller JAM (a job reservation in the main body is not released) A job reservation is not released after a lapse of a given time after that a print start command has been received. or more, and turn ON the main power switch. Page 1 BIZHUB 558/368 QUICK REFERENCE How to use the system – Panel Operating the touch screen* Mobile access area (NFC) 1. (bizhub 658e Code: C9401, C9402 Description: bizhub 658e/558e/458e • C9401: Exposure LED lighting failure • C9402: Exposure LED lighting abnormally • C9401: The output from the CCD sensor is a predetermined value or less during CCD sensor gain adjustment. Causes: Remedy: 1 Initial check items - - 2 Open and close the front door of the main body. X. The protocol is not initialized. <When FS-536 or FS-536SD is installed> The sub tray exit sensor (PS8) is not turned OFF (unblocked) even after the set period of time has elapsed after it is turned ON (blocked). Collapse. Auto document feed Section 6; 7. Description. Causes: • Transport motor (M1) (bizhub 558e/458e) • Paper feed motor (M22) • Registration motor (M24) (bizhub 658e) • Registration clutch (CL4) (bizhub 558e/458e) • Registration sensor/1 (PS1) • Registration sensor/2 (PS72) (bizhub 658e/558e) • Expansion control board (EXCB) • Code. Remedy: 1 Check the fusing unit for correct installation (whether it is secured in position). 2 Check the connector between M3-PRCB CN2 for proper connection and correct as necessary. Code: 14-01, 14-40 Description: bizhub 658e/558e/458e Misfeed at tray 4 feed section 14-01 The leading edge of the paper is not turned ON the tray 4 vertical transport sensor (PS123) even after the lapse of a given period of time after the tray 4 starts to feed paper. Code: 72-70 Description: Misfeed at PK JAM. 4 Replace PRCB. Enabling the i-Option function 1 Prepare at hand the token certificate supplied with i-Option. 41 Paper remains detected at the sensor (tray 3 pass-through) although the printer is idle. Error Code: Code: C0108 Description: Tray 4 paper feed motor turning at abnormal timing (When PC-213 is installed) • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. Re: C3bo3. Code: 6751 Description: CCD clamp/gain adjustment failure During the CCD gain adjustment, a condition in which the peak value of the output data is equal to, or less than, 64 occurs three consecutive times during retries. antone. 3. Konica-Minolta bizhub C25 All About this machine. Remedy: 1 Reinstall the old PRCB. 100. (bizhub 368e/308e / bizhub 658e/558e/458e) 4. You can check the action to take as well as a description of the error by referring to the code in Paper jam of a sheet of paper left at the 2nd transfer section results, if the registration sensor/1 (PS1) is turned ON (unblocked) when the main power switch is turned Code: 10-01, 10-02, 10-04, 10-40 Description: bizhub 658e/558e/458e Misfeed at manual bypass feed section 10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor/1 (PS1) even after the lapse of a given period of time after the manual bypass tray starts to Code: C3B03 Description: IH malfunction (monitor) <bizhub 554e> Though the IH heater is OFF, mechanically, the ON status is detected. Konica-Minolta bizhub C35 Used for the following models. Unformatted hard disk is connected. Page of 1. <bizhub 554e> When the machine is in standby mode after a predetermined period of time after the warm-up stage is started, detected temperature of the heating roller temperature sensor (TEMS) lower than a given temperature for a given period of time consecutively. Post Cancel. Causes: • Tray 4 paper feed motor (M121) • Konica-Minolta bizhub C203; Konica-Minolta bizhub C253; Konica-Minolta bizhub C353; Konica-Minolta bizhub C353P Used for the following models. Auto Konica-Minolta bizhub C258; Konica-Minolta bizhub C308; Konica-Minolta bizhub C368; Konica-Minolta bizhub C458; Konica-Minolta bizhub C558; Konica-Minolta bizhub C658 Code: 13-01, 13-40 Description: bizhub 368e/308e Misfeed at tray 3 feed section. Konica Minolta. Error Code: For details, see “Entering the machine type information (bizhub 368e/308e / bizhub 658e/558e/458e)”. info service 2001 - 2024. (bizhub 368e/308e / bizhub 658e/558e/458e) 7. 07-23-2018, 05:45 PM. Code: 10-01, 10-02, 10-04, 10-40 Description: bizhub 658e/558e/458e Misfeed at manual bypass feed section 10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor/1 (PS1) even after the lapse of a given period of time after the manual bypass tray starts to Code: 10-01, 10-02, 10-04, 10-40 Description: bizhub 658e/558e/458e Misfeed at manual bypass feed section 10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor/1 (PS1) even after the lapse of a given period of time after the manual bypass tray starts to Code: 30-03 Description: bizhub 658e/558e/458e Misfeed at 2nd transfer section 30-03 The leading edge of paper is not turned ON (unblocked) the paper exit sensor (PS3) since the paper feeding is started. The tray 1 upper limit sensor (PS6) is not blocked even after the lapse of a given period of time after the lifting motion has been started. Code: C5370 Description: bizhub 368e/308e Machine rear side cooling fan failure to turn. Auto document feed Section; 2. Check the fusing unit for correct installation (whether it is secured in position). An invalid operation occurred. And Konica-Minolta bizhub 308e; Konica-Minolta bizhub 368e; Konica-Minolta bizhub 458e; Konica-Minolta bizhub 558e; Konica-Minolta bizhub 658e The C3B03 error code is likely secondary to an initial service code. Konica-Minolta bizhub C35 Konica Minolta. 66-12 A StreetPass communication Code: C2558 Description: Abnormally high toner density detected TCR sensor board - The T/C ratios detected by the TCR sensor board (TCRSB) are above the threshold for the detection of abnormally high T/C ratio for three successive times. Used for the following models. Code: 10-01, 10-02, 10-04, 10-40 Description: bizhub 658e/558e/458e Misfeed at manual bypass feed section 10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor/1 (PS1) even after the lapse of a given period of time after the manual bypass tray starts to Code: 10-01, 10-02, 10-04, 10-40 Description: bizhub 658e/558e/458e Misfeed at manual bypass feed section 10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor/1 (PS1) even after the lapse of a given period of time after the manual bypass tray starts to Konica-Minolta bizhub 558e. bizhub 658e/558e/458e; bizhub 368e/308e; Replacing a Waste Toner Box. Check the connector between TEMS/1-relay CN109-MFPB CN15E for proper connection and correct as necessary. Code: 10-01, 10-02, 10-04, 10-40 Description: bizhub 658e/558e/458e Misfeed at manual bypass feed section 10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor/1 (PS1) even after the lapse of a given period of time after the manual bypass tray starts to Code: C6756 Description: CCD power-supply voltage malfunction. Trusted Tech. Filter. Check the fusing unit-MFPB CN12E for proper connection and correct or change as necessary. A protocol error occurred. 2 Check M1 for proper drive coupling Konica-Minolta; bizhub 558e #519; Konica-Minolta bizhub 558e. Troubleshooting steps include: 1. • The scanner home sensor is unable to detect a scanner even when the scanner motor has been driven to move the scanner over the maximum travelling distance. The boot diagnosis is performed when the start screen on the touch panel of the machine freezes or blacks out for some faulty condition. Replace IHPU. Check the connector between CUDB CN1 M4 load check • Check code: 60 • Multi code: 81, 82 • Control signal: DFCB J18-4 to 5 • Location of electrical component: DF-704 1-G 6. If a USB flash drive has been used, first remove the USB flash drive and then turn ON the main power switch. 250+ Posts. <When FS-533+PK-519 is installed> The paper feed sensor (PS201) is not turned OFF even after the set period of time has elapsed after it is turned ON. The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. . 1 G00-00 2018-05-17 Firmware: Eng: USD 14. Error Code: Code: 10-01, 10-02, 10-04, 10-40 Description: bizhub 658e/558e/458e Misfeed at manual bypass feed section 10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor/1 (PS1) even after the lapse of a given period of time after the manual bypass tray starts to Code: C4801 Description: Main unit board failure MFP detects simultaneous replacement of multiple boards. You may have to register before you can post: click the register link above to proceed. Auto document feed Section 3 ; 4. Error Code: Code: S-2 Description: CIS gain adjustment failure (bizhub 368e/308e: When DF-704 is installed, bizhub 658e/558e/458e). When I try to scan documents using our Konica Minolta printer, the process works intermittently. bizhub 658e/558e/458e; bizhub 368e/308e; Replacing a Staple Cartridge of the Finisher or Saddle Stitcher. If still have the same error, kindly proceed to do a Trouble About Network Error Codes. (bizhub 368e/308e / bizhub 658e/558e/458e) 5: Light up in purple: Light up: Software: Software trouble: 1. FM1 load check • Check code: 60 • Multi code: 113 • Control signal: DFCB J16-3 (ON) • Location of electrical component: DF-704 7-G 4. 36. Replace MFPB. 7. Causes: • Fusing power supply cooling fan (FM12) • Expansion control board (EXCB) • Printer control board (PRCB) Remedy: 1 Check the connector between FM12-EXCB CN6 for All About this machine. Power is not supplied to CCD after the lapse of a given period of time after the main power switch or power key is turned ON or the machine recovers from the sleep mode. Causes: • Transport motor (M1) • Tray 1 paper feed clutch (CL3) • Registration clutch (CL4) • Registration sensor (PS1) • Front side board (FRB) • MFP board (MFPB) Code: C3102 Description: Fusing roller failure to turn • When the IH power supply is turned ON, pulse signals are not input either of the heating roller rotation sensor within a predetermined period of time. Auto document feed Section 8; 9. Replace the transfer belt unit. 6. Causes: • Transport motor (M1) • Printer control board (PRCB) Remedy: 1 Check the connector between M1-PRCB CN31 for proper connection and correct as necessary. Check for clogging in the ventilation path between the MFPB and the power supply cooling fan, and correct as necessary. Causes: • Fusing unit • C3822: Fusing temperature sensor/2 (TEM2) • C3825: Fusing temperature sensor/1 (TEM1: center) • Code: 13-01, 13-40 Description: Misfeed at tray 3 feed section. PANEL BLACKOUT. period at any time 1 sec. Auto document feed Section 2; 3. Code: C1104 Description: bizhub 658e/558e/458e Stacker plate drive motor malfunction <When FS-537 or FS-537SD is installed> The stacker plate home sensor (PS30) is not turned OFF (unblocked) or ON (blocked) even after the set period of time has elapsed after the stacker plate drive motor (M3) is turned ON. 1. 66-02 The after separate sensor (PS4) is not turned ON after a lapse of a given time after the take-up motor (M1) is turned ON. Causes: • Machine rside cooling fan (FM3) • MFP board (MFPB) Remedy: 1 Check the connector between FM3-MFPB PJ26 for proper connection and correct as necessary. Error Code: Code: 13-01 Description: Misfeed at tray 3 feed section. 3 Check the PWB-M connector for proper connection and correct as Code: 14-01, 14-40 Description: bizhub 658e/558e/458e Misfeed at tray 4 feed section 14-01 The leading edge of the paper is not turned ON the tray 4 vertical transport sensor (PS123) even after the lapse of a given period of time after the tray 4 starts to feed paper. Remedy: 1 Check the M1 connector for proper connection and correct as necessary. The C3102 codes mean Fusing release code drive motor for fuser or home release sensor not working. Code: C5501 Description: AC signal abnormality The zero cross signal is not input during fusing phase control. (bizhub 658e/558e / bizhub 458e) 7. Join Date: Oct 2014; Posts: 344 #4. 5. document to the intended place. 20-01 The registration sensor/1 (PS1) is not turned ON (unblocked) even after the lapse of a given period of time after the paper has turned ON the tray 2 vertical transport sensor (PS19). The network connection is busy. Posts; Latest Activity; Photos . 13-01 The leading edge of the paper is not turned ON the tray 3 vertical transport sensor (PS113) even after the lapse of a given period of time after the tray 3 starts to feed paper. All About this machine. Finisher FS-537 Code: C3826 Description: Fusing abnormally low temperature (TEM1: edge) The fusing temperature sensor/1 (TEM1: edge) continues to detect a temperature lower than a predetermined one for a predetermined period of time after warm-up is complete. 2 Check the connector between M125-PCCB CN8 for proper connection and correct as necessary. Code: C8101; Description: bizhub 658e/558e/458e Before reading pressure welding alienation mechanism trouble. Code: C5370 Description: Machine rear side cooling fan’s failure to turn. Code: CC163 Description: ROM contents error (PRT). Auto document feed Section 5; 6. Causes: <When FS-537 or FS-537SD is installed> • FNS entrance sensor (PS34) • FNS middle sensor (PS36) • Used for the following models. We do not sell these spare parts! We only help you to create your parts list for request from your suppliers. The boot diagnosis can be performed automatically to identify a cause of a Code: C6102 Description: Drive home sensor malfunction • The scanner home sensor is unable to detect the scanner located at its home position. (Malfunction of IH heater operation) Causes: • Fusing unit • IH coil unit (IHC) • IH magnetic erasing board (IHMEB) • Printer control board (PRCB) Remedy: 1 Check the fusing unit for correct installation (whether it is secured in position). Internal error of the certificate verification (PKI) function (EAP-TLS/EAP-TTLS/PEAP). 45 Paper fed from tray 4 Code: C1183 Description: Elevate drive malfunction <When FS-527 is installed> • During downward movement, the tray 2 upper limit sensor (PS24) is turned OFF and the tray 2 lower limit sensor (PS21) is turned ON. 4. To ensure the best possible performance and ef- Remedy: 1 Check the fusing unit for proper installation and correct as necessary. Auto document feed Section 4; 5. If the trouble code appears again, contact your Service Representative. Table Of Contents Troubleshooting. 36 Paper fed from tray 3 was picked but it never reached the sensor (tray 2 pass-through). Code: 10-01, 10-02, 10-04, 10-40 Description: bizhub 658e/558e/458e Misfeed at manual bypass feed section 10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor/1 (PS1) even after the lapse of a given period of time after the manual bypass tray starts to Konica-Minolta BIZHUB 558E movie 4. bizhub 658e/558e/458e; bizhub 368e/308e; Replacing a Drum Unit. <bizhub 554e> A failure in communication with the fusing CPU continues for a predetermined period of time. Error Code: In unserem Download Center finden Sie die wichtigsten Treiber, Bedienungsanleitungen sowie Software für unsere Konica Minolta bizhub und Accurio Systeme. Causes: Heating roller rotation sensor/1 (PS56) Fusing motor (M30) Printer control board (PRCB) Fusing unit Remedy: 1 Check the fusing unit for proper installation and correct Unable to check for expiration because the CRL size that has been retrieved to check for the expiration of the server certificate exceeds the maximum capacity that can be retained (1MB) (EAP-TLS/EAP-TTLS/PEAP). To start viewing messages, select the forum that you want to visit from the selection below. Check the connector between hard disk (B)-MFPB CN7, CN11 for proper connection and correct as necessary. Konica-Minolta bizhub C35 Code: C0202 Description: Tray 1 feeder up/down abnormality. Part Number: 1. 13-01 The leading edge of the paper does not turn ON (block) the tray 3 paper feed sensor (PS21) even after the lapse of a given period of time after the tray 3 starts to feed paper. (bizhub 658e/558e) 6. Code. Causes: • MFP board (MFPB) • Hard disk Remedy: 1 Select [Service Mode] -> [State Confirmation] -> [Memory/HDD Adj. (bizhub 658e/558e/458e) 5. (IH heater operation failure) • Though the IH heater is OFF, mechanically, the ON status is detected. (bizhub 658e Code: C5102 Description: Main Motor's failure to turn • The Motor Lock signal remains HIGH for a predetermined continuous period of time while the Motor is turning. Resetting the C3B03 code and power cycling the machine. The zero cross signal is not input during fusing phase control. When using the authentication device, authentication data is not to meet the specifications. Causes Code: 10-01, 10-02, 10-04, 10-40 Description: bizhub 658e/558e/458e Misfeed at manual bypass feed section 10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor/1 (PS1) even after the lapse of a given period of time after the manual bypass tray starts to User's Guide CD. Code: 72-23 Description: Misfeed at FS transport section. Check the fan for possible overload and correct as necessary. 13-40 For paper fed from the tray 3, the image write start signal permit continues to be disabled for a predetermined period of time Code: C9404 Description: CIS LED lighting abnormally <When DF-701 is installed> After a scan job is completed, the machine detected that the average output of the CIS LED is greater than the specified value. ](Only in bizhub 658e/558e/458e ) The machine malfunctioned and is unable to make copies. Code: CC211 Description: Authentication device general error. <When FS-537+PI-507 or FS-537SD+PI-507 is installed> • When a paper is fed from the upper tray, the paper entrance sensor /Lw (PS206) is not turned ON (unblocked) even after the set period of time has elapsed after the transfer clutch /Up (CL201) turns ON by a paper. 2 Back up data. The motor lock signal remains Code: CFDD# CFE0# Description: bizhub 658e/558e/458e Abort code Causes: Dual scan image processing board (DSIPB) Remedy: 1. 5 M3 operation check PRCB CN2-9 (REM) PRCB CN2-12 (LOCK) bizhub C554 22-J Code: C0108 Description: Tray 4 paper feed motor turning at abnormal timing. Code: C5102 Description: Transport motor’s failure to turn The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. The motor lock signal remains HIGH for a predetermined continuous time while the motor remains stationary. Code: C5372 Description: MFP control board CPU temperature failure Temperature failure of CPU on the MFP board was detected. Replace DFCB. Replace the hard disk. Time. 11. Replace FM1. 3 Check the connector of M3 for proper drive coupling and correct as necessary. Remedy: 1 Check the connector between M1-PRCB CN31 for proper connection and correct as necessary. Call the Service Mode to the screen. Code: C0108 Description: Tray 4 paper feed motor turning at abnormal timing <When PC-210 is installed> • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. The number of search results has exceeded the maximum number of items (bizhub 558e/458e only) - Paper jam of a sheet of paper left at the exit section results, if the paper exit sensor (PS3) is turned ON (unblocked) when the main power switch is turned ON, a door Description: bizhub 658e/558e/458e Misfeed at tray 4 feed section 14-01 The leading edge of the paper is not turned ON the tray 4 vertical transport sensor (PS123) even after the lapse of a [An internal has error occurred. It is detected that the CIS clamp gain adjustment value is faulty. Check the connector between FM3-relay CN301-MFPB CN13 for proper connection and correct as Code: 99-01 Description: bizhub 368e/308e Controller JAM (paper size error) • As a result of a paper size error, the controller transmits a forced stop command to Konica-Minolta bizhub C258; Konica-Minolta bizhub C308; Konica-Minolta bizhub C368; Konica-Minolta bizhub C458; Konica-Minolta bizhub C558; Konica-Minolta bizhub C658 For details, see “Entering the machine type information (bizhub 368e/308e / bizhub 658e/558e/458e)”. Tray 4 is the paper source. • The motor lock signal remains LOW for a predetermined continuous period of time while the motor remains stationary. Code: C8302; Description: bizhub 658e/558e/458e Cooling fan motor failure. Code: C3B07, C3B08 Description: bizhub 658e/558e • C3B07: IH input power error (bizhub 658e/558e) • C3B08: IH input voltage error (bizhub 658e/558e) C3B07 3. Replacing a Staple Cartridge; Replacing a Saddle Staple Cartridge; Punch Scrap Processing. ATTENTION: If trouble code is showing on the machine control panel, kindly restart the machine by turning OFF the main power for 10 seconds and turn it back ON after. 43 Paper fed from tray 4 never reached the sensor (tray 3 pass-through). Replace the MFP board. 92. Tap to select or determine 6. 2 Code: 20-01, 20-02, 20-04 Description: bizhub 658e/558e/458e Misfeed at vertical transport section. Drag & Drop to move a a menu. Code: 99-04 Description: bizhub 658e/558e/458e Controller JAM Code: 72-35 Description: Misfeed at PI section. Call the Enhanced Security to the screen. Boot diagnosis function. 2 Hi everyone, I need some assistance with an issue I’m experiencing. If this is your first visit, be sure to check out the FAQ by clicking the link above. Causes: • Fusing unit • IH coil unit (IHC) • IH power supply (IHPU) • IH magnetic erasing board (IHMEB) • Printer control board (PRCB) Remedy: 1 Check the fusing unit for correct installation (whether it is secured in Code: CFDD# CFE0# Description: bizhub 658e/558e/458e Abort code Causes: Dual scan image processing board (DSIPB) Remedy: 1. <bizhub 554e> • While the IH heater was ON, input power stayed at the high voltage power detection value or over for Code: C3B07, C3B08 Description: bizhub 658e/558e • C3B07: IH input power error (bizhub 658e/558e) • C3B08: IH input voltage error (bizhub 658e/558e) C3B07 Code: CC163 Description: ROM contents error (PRT). (bizhub 458e) 5. (HDD (A) (bizhub 368e/308e / bizhub 658e/558e/458e) / HDD (B)) 7. 3 Check the connector between PS114- PCCB CN6 for proper connection and Award winning multifunctional printer bizhub 558e by Konica Minolta includes cost-saving & energy-saving modes as well as mobile printing! Get a quote now! Get a quote now! Support & Downloads Konica-Minolta bizhub 558e. The device is not connected to the network. Auto document feed Section 7; 8. Causes: • Exhaust fan/1 (FM1) • Exhaust fan/2 (FM2) • Exhaust fan/3 (FM3) • Clean unit drive board (CUDB) • MFP board (MFPB) Remedy: 1. • During warm up, the temperature Чорно-білий багатофункціональний пристрій А3 формату ★ bizhub 558e ★ від Konica Minolta ☛ сенсорна Code: C2350 Description: bizhub 658e/558e/458e Toner suction fan failure to turn. Causes: • Tray 4 paper feed motor (M121) • Code: C3102 Description: Heating roller assy failure to turn During any state other than printing operation , the hard latch signal from one or both of the heating roller rotation latch detection 1 and the heating roller rotation latch detection 2 is turned ON. Error Code: Service Mode, Troubleshooting: Parts Catalog: Email: Password: Sign In : New Register: Forgot Password? Code: 10-01, 10-02, 10-04, 10-40 Description: bizhub 658e/558e/458e Misfeed at manual bypass feed section 10-01 The leading edge of the paper is not turned ON (unblocked) the registration sensor/1 (PS1) even after the lapse of a given period of time after the manual bypass tray starts to (bizhub 368e/308e) 4. Part Number: Fusing Drive Section. 2 Code: C5501 Description: AC signal abnormality. Correct the harness connection between CIS and DSIPB if faulty. bizhub 658e/558e/458e 1-2 1. • C9402: The average output value of the CCD sensor with the scanner at its standby position is a predetermined value or Code: 11-01 Description: The leading edge of the paper is not turned ON (unblocked) the registration sensor (PS1) even after the lapse of a given period of time after the tray 1 starts to feed paper. The time limit is exceeded. PrintCopy . Parts Catalog page All About this machine. Causes: • CIS module (CIS) • Dual scan image processing board (DSIPB) • MFP board (MFPB) Remedy: 1. All Time Today When [Administrator Settings] -> [Security Settings] -> [Security Details] -> [Prohibited Functions When Authentication Error] is set to “Mode 2”, operation will be prohibited since it indicates authentication failure by failing to enter the correct CE password within Code: 11-01 Description: The leading edge of the paper is not turned ON (unblocked) the registration sensor (PS1) even after the lapse of a given period of time after the tray 1 starts to feed paper. They refer to codes displayed when an error occurs in the network. 3 Replace fusing unit. after the Main Motor has started turning. Clean the joint or correct if necessary. Turn OFF and ON the main power switch. Reinstall the hard disk. 243. 2. 2 Check the fan for possible Code: C0108 Description: Tray 4 paper feed motor turning at abnormal timing <When PC-210 is installed> • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor remains stationary. Code: C0108 Description: Tray 4 paper feed motor turning at abnormal timing (When PC-213 is installed) • The motor lock signal remains HIGH for a predetermined continuous period of time while the motor is turning. Causes: Remedy: Initial check items Open and close the front door of the main body. Check the connector between FM11-relay CN62-MFPB CN31E for proper connection and correct as necessary. 4 PS37 I/O check, sensor check. Error Code: Code: C0206 Description: Tray3 lift-up failure • The lift-up upper sensor is not blocked even; Remedy: 1 Check the connector between M124-PCCB CN4 for proper connection and correct as necessary. Konica-Minolta bizhub 308e; Konica-Minolta bizhub 368e; Konica-Minolta bizhub 458e; Konica-Minolta bizhub 558e; Konica-Minolta bizhub 658e Code: CD010 Description: Hard disk unformat. Replace HV. D341. 00 2. (bizhub 368e/308e / bizhub 658e/558e/458e) Code: P-32; Description: bizhub 658e/558e Heating roller temperature sensor/1 temperature detection failure. Konica-Minolta bizhub C35 Code: 20-01, 20-02, 20-04 Description: bizhub 658e/558e/458e Misfeed at vertical transport section. Code: 72-11 Description: Misfeed at FS transport section. iflpxj jfcoo flafpm vecjry qfjupw hcqves qiow ndgr ofbl xlpgle